Improving In-Vehicle Air Quality with Bio-Additive ABS Composites
Main Article Content
Abstract
In recent years, significant research efforts have focused on improving indoor air quality in vehicles and reducing volatile organic compound (VOC) emissions. Interior trim components release harmful gases, particularly under elevated temperature conditions, due to the degradation of organic structures, posing health risks to passengers. This risk is especially critical for children and animals who are exposed to prolonged travel periods in service vehicles. In this study, bio-based additives were incorporated into recycled acrylonitrile butadiene styrene (ABS) matrices used in interior trim sheet production to reduce environmental impacts and improve thermal performance. A mixture obtained from marine-origin algae and terrestrial plant powders (nettle, oak, and poplar leaves) was added to recycled ABS at 2 wt%. Total Organic Carbon (TOC) measurements were conducted under ambient conditions. Results showed that carbon emissions from bio-additive plates were 87.7% lower than those from non-additive plates. These findings demonstrate that natural additives exhibit gas adsorption capabilities within ABS matrices and offer an effective and sustainable alternative for improving in-vehicle air quality. In this context, the present work provides an important contribution both to recycling-based polymer utilization and to the development of eco-friendly, bio-composite automotive materials.
Downloads
Article Details
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
References
Faber, J., & Brodzik, K. (2017). Air quality inside passenger cars. AIMS Environmental Science, 4(1), 112-133. DOI: https://doi.org/10.3934/environsci.2017.1.112
Horvat, T., Pehnec, G., & Jakovljević, I. (2025). Volatile Organic Compounds in Indoor Air: Sampling, Determination, Sources, Health Risk, and Regulatory Insights. Toxics, 13(5), 344. DOI: https://doi.org/10.3390/toxics13050344
Xu, B., Chen, X., & Xiong, J. (2018). Air quality inside motor vehicles' cabins: a review. Indoor and Built Environment, 27(4), 452-465. DOI: https://doi.org/10.1177/1420326X16679217
Klepeis, N. E., Nelson, W. C., Ott, W. R., Robinson, J. P., Tsang, A. M., Switzer, P., ... & Engelmann, W. H. (2001). The National Human Activity Pattern Survey (NHAPS): a resource for assessing exposure to environmental pollutants. Journal of exposure science & environmental epidemiology, 11(3), 231-252. DOI: https://doi.org/10.1038/sj.jea.7500165
Liu, Z., Nicolai, A., Abadie, M., Qin, M., Grunewald, J., & Zhang, J. (2021, April). Development of a procedure for estimating the parameters of mechanistic VOC emission source models from chamber testing data. In Building Simulation (Vol. 14, No. 2, pp. 269-282). Beijing: Tsinghua University Press. DOI: https://doi.org/10.1007/s12273-020-0616-3
Sato, S. (2004). Air quality in auto-cabin. R&D Review of Toyota CRDL, 39(1), 36-43.
Kim, H. J., Jeong, C., Oh, A., Seo, Y. S., Jeon, H., & Eom, Y. (2024). Elevated volatile organic compound emissions from coated thermoplastic polyester elastomer in automotive interior parts: Importance of plastic swelling. Journal of Hazardous Materials, 461, 132614. DOI: https://doi.org/10.1016/j.jhazmat.2023.132614
Jiang, X., Jiang, J., Chen, D., Zhou, W., & Zhu, B. (2020). Dynamic material flow analysis of Chinese passenger car plastics. China Environ. Sci, 40, 4106-4114.
Faber, J., Brodzik, K., Gołda-Kopek, A., & Łomankiewicz, D. (2013). Air Pollution in New Vehicles as a Result of VOC Emissions from Interior Materials. Polish Journal of Environmental Studies, 22(6).
Horvat, D., Jäger, A., & Lerch, C. M. (2025). Fostering innovation by complementing human competences and emerging technologies: an industry 5.0 perspective. International Journal of Production Research, 63(3), 1126-1149. DOI: https://doi.org/10.1080/00207543.2024.2372009
Dobrotă, D., Bărbușiu, A. M., Sava, G. A., & Oleksik, V. Ș. (2025). Functional Additives in Automotive Polymer Matrices: Compatibility, Mechanisms, and Industry Challenges. Polymers, 17(17), 2328. DOI: https://doi.org/10.3390/polym17172328
Naik, V., & Kumar, M. (2021). A review on natural fiber composite material in automotive applications. Engineered Science, 18(18), 1-10. DOI: https://doi.org/10.30919/es8d589
Yıldızhan, Ş., Çalık, A., Özcanlı, M., & Serin, H. (2018). Bio-composite materials: a short review of recent trends, mechanical and chemical properties, and applications. European Mechanical Science, 2(3), 83-91. DOI: https://doi.org/10.26701/ems.369005
Perrin, D., Clerc, L., Leroy, E., Lopez-Cuesta, J. M., & Bergeret, A. (2008). Optimizing a recycling process of SMC composite waste. Waste Management, 28(3), 541-548. DOI: https://doi.org/10.1016/j.wasman.2007.03.026
Ashori, A., & Nourbakhsh, A. (2009). Characteristics of wood–fiber plastic composites made of recycled materials. Waste management, 29(4), 1291-1295. DOI: https://doi.org/10.1016/j.wasman.2008.09.012
Al-Salem, S. M., Lettieri, P., & Baeyens, J. (2009). Recycling and recovery routes of plastic solid waste (PSW): A review. Waste management, 29(10), 2625-2643. DOI: https://doi.org/10.1016/j.wasman.2009.06.004
Turku, I., Kärki, T., & Puurtinen, A. (2018). Durability of wood plastic composites manufactured from recycled plastic. Heliyon, 4(3). DOI: https://doi.org/10.1016/j.heliyon.2018.e00559
Kamdem, D. P., Jiang, H., Cui, W., Freed, J., & Matuana, L. M. (2004). Properties of wood plastic composites made of recycled HDPE and wood flour from CCA-treated wood removed from service. Composites Part A: Applied Science and Manufacturing, 35(3), 347-355. DOI: https://doi.org/10.1016/j.compositesa.2003.09.013
Leu, S. Y., Yang, T. H., Lo, S. F., & Yang, T. H. (2012). Optimized material composition to improve the physical and mechanical properties of extruded wood–plastic composites (WPCs). Construction and Building Materials, 29, 120-127. DOI: https://doi.org/10.1016/j.conbuildmat.2011.09.013
Koronis, G., Silva, A., & Fontul, M. (2013). Green composites: A review of adequate materials for automotive applications. Composites Part B: Engineering, 44(1), 120-127. DOI: https://doi.org/10.1016/j.compositesb.2012.07.004
John, M. J., & Thomas, S. (2008). Biofibres and biocomposites. Carbohydrate polymers, 71(3), 343-364. DOI: https://doi.org/10.1016/j.carbpol.2007.05.040
Bledzki, A. K., & Gassan, J. (1999). Composites reinforced with cellulose based fibres. Progress in polymer science, 24(2), 221-274. DOI: https://doi.org/10.1016/S0079-6700(98)00018-5