Orclever Proceedings of Research and Development

Cuo Nanopartikülünün Hidrolik Dişli Pompa Performansına Etkisi

Abdullah Yıldız

Uşak University

https://orcid.org/0000-0003-4831-0975

Halil Aslan

Uşak University

DOI: https://doi.org/10.56038/oprd.v3i1.401

Keywords: Hydraulic gear pump, Hydraulic oil, CuO nanoparticle, Performance

---

Abstract

In this study, an experimental setup for hydraulic pump tests was designed and built. The mechanical power, hydraulic power, mechanical losses, electrical losses, volumetric losses and energy, isentropic and volumetric efficiencies of the hydraulic pump using nano fluid (HO + CuO) obtained by adding 0.1% CuO nano particles into HO with the hydraulic pump using hydraulic oil (HO) as the working fluid were compared experimentally. In the experiments, electricity consumption (kWh) and volume flow rate (lt/min) were measured for four different pressure drops such as 80 bar, 100 bar, 120 bar and 140 bar. As a result, the addition of nanoparticles increased electricity consumption from 5% to 14%, energy efficiency by about 4%, volumetric efficiency from 4% to 19% and isentropic efficiency from 4% to 20%. In addition, the addition of nanoparticles reduced volumetric losses from 68% to 172% and mechanical losses from 20% to 50%, while increasing electrical losses by 2% to 10%.

---

References

Aslan H., 2019, Hidrolik pompalarda CuO nanopartikül kullanımının enerji performansına etkisinin araştırılması, Yüksek Lisans Tezi, Uşak Üniversitesi, Uşak, Türkiye.

Torrent, M., Gamez-Montero, P.J., Codina, E., 2021, Parameterization, Modeling, and Validation in Real Conditions of an External Gear Pump, Sustainability, 13 (6), 3089. DOI: https://doi.org/10.3390/su13063089

Li, W., Mckeown, A., Yu, Z., 2020, Correction of cavitation with thermodynamic effect for a diaphragm pump in organic Rankine cycle systems, Energy Reports, 6 (3), 2956-2972. DOI: https://doi.org/10.1016/j.egyr.2020.10.013

Kumar N., Sarkar B.K., Maity S., 2020, Recent Development and Application of the Hydrostatic Transmission System, Advances in Mechanical Engineering. Lecture Notes in Mechanical Engineering. Springer, Singapore, 1613-1625. DOI: https://doi.org/10.1007/978-981-15-0124-1_141

Zardin, B., Natali, E., Borghi, M., 2019, Evaluation of the Hydro—Mechanical Efficiency of External Gear Pumps, Energies, 12(13), 2468. DOI: https://doi.org/10.3390/en12132468

Sliwinski, P., 2020, The Influence of Water and Mineral Oil on Mechanical Losses in a Hydraulic Motor for Offshore and Marine Applications, Polish Maritime Research, 27(2 (106)),125-135. DOI: https://doi.org/10.2478/pomr-2020-0034

Yang, Y., Zhang, H., Xu, Y., Zhao, R., Hou, X., Liu, Y., 2018, Experimental study and performance analysis of a hydraulic diaphragm metering pump used in organic Rankine cycle system, Applied Thermal Engineering, 132, 605-612. DOI: https://doi.org/10.1016/j.applthermaleng.2018.01.001

Zhang, J.,Li, Y., Xu, B., Chen, X., Pan, M., 2018, Churning losses analysis on the thermal-hydraulic model of a high-speed electro-hydrostatic actuator pump, International Journal of Heat and Mass Transfer, 127, 1023-1030. DOI: https://doi.org/10.1016/j.ijheatmasstransfer.2018.06.133

Zeleny Z., Vodicka V., Novotny V., Mascuch J., 2017, Gear pump for low power output ORC – an efficiency analysis”, Energy Procedia 129, 1002-1009. DOI: https://doi.org/10.1016/j.egypro.2017.09.227

Michael, P., Khalid, H., and Wanke, T., 2012, An Investigation of External Gear Pump Efficiency and Stribeck Values, SAE Technical Paper, 2012-01-2041, https://doi.org/10.4271/2012-01-2041. DOI: https://doi.org/10.4271/2012-01-2041

Ünlü A., 2005, Traktörlerin Hidrolik pompa karakteristiklerinin incelenmesi, Yüksek Lisans Tezi, Ankara Üniversitesi, Ankara, Türkiye.

Chavda N. K, Patel G. V. , Bhadauria M. R., M. Makwana N., 2015, Effect of Nanofluid on Efficiency of Centrifugal Pump”, International Journal of Research in Engineering and Technology , 4 (4), 701-705. DOI: https://doi.org/10.15623/ijret.2015.0404121

Martorana P.J., 2011, Effect of carbon based nano additives on external gear pump performance, Degree of Master, University of Illinois at Urbana-Champaign, Aerospace Engineering, Urbana USA.

Rizzo G., Bonanno A., Paolo G., Massarotti G. P., Pastorello L., Raimondo M., Veronesi F., Magda Blosi M., 2016, Energy efficiency improvement by application of nano structured coatings on axial piston pump slippers”, Institute for Agricultural and Earthmoving Machines – IMAMOTER – C.N.R., Italy 10th International Fluid Power Conference, Dresden, 313-328.

Rizzo G., Massarotti G. P., Bonanno A., Paoluzzi R., Raimondo M., Blosi M., Veronesi F., Caldarelli A., Guarin G., 2015, Axial piston pumps slippers with nanocoated surfaces to reduce friction. International Journal of Fluid Power, 16 (1), 1–10. DOI: https://doi.org/10.1080/14399776.2015.1006979

Nasiri-Khuzani Gh., Asoodar M. A., Rahnama M., Sharifnasab H., 2012, Evaluation of engine parts wear using nano lubricant oil in agricultural tractors nano lubrication, Global Journal of Science Frontier Research Agriculture and Veterinary Sciences, 12 (8), 36-41.